View Full Version : Give us a clue... (Fixed IP)
I can't connect with fixed IP on a WPA Wireless network.
Roaming and automaticly assigned IPs work but when I try to set the two
wireless machines to fixed IPs they won't connect. (one is WinXP, other
Ubuntu)
Gateway is 192.168.2.1 a wired machine is ...2.2 and I wanted the two
wireless ones to be ...2.3 & ...2.4
(I wanted to do it for port forwarding.)
Any ideas what I should be looking for?
TIA
Slatts
Jeff Liebermann
05-17-08, 10:35 PM
On Sat, 17 May 2008 18:57:12 +0100, "Sla#s" <phil@KNOTslatts.net>
wrote:
>I can't connect with fixed IP on a WPA Wireless network.
>Roaming and automaticly assigned IPs work but when I try to set the two
>wireless machines to fixed IPs they won't connect. (one is WinXP, other
>Ubuntu)
>Gateway is 192.168.2.1 a wired machine is ...2.2 and I wanted the two
>wireless ones to be ...2.3 & ...2.4
>(I wanted to do it for port forwarding.)
>
>Any ideas what I should be looking for?
Nope. No ideas. I have no clue what you're talking about, what
you're trying to accomplish, why you need static IP's on the clients,
how these clients are actually configured, what exact operating
systems are being used, what device you're connecting to, whether the
static IP's you picked are already in use, what diagnostics you've
tried, and what other hardware you have to work with. Try a better
description of what you have to work with and what you're trying to
accomplish.
--
# Jeff Liebermann 150 Felker St #D Santa Cruz CA 95060
# 831-336-2558 jeffl@comix.santa-cruz.ca.us
# http://802.11junk.com jeffl@cruzio.com
# http://www.LearnByDestroying.com AE6KS
To restore balance to the world Sla#s wrote in
g0n6c4$cqe$2@energise.enta.net
>> I can't connect with fixed IP on a WPA Wireless network.
>> Roaming and automaticly assigned IPs work but when I try to set the
>> two wireless machines to fixed IPs they won't connect. (one is
>> WinXP, other Ubuntu)
>> Gateway is 192.168.2.1 a wired machine is ...2.2 and I wanted the
>> two wireless ones to be ...2.3 & ...2.4
>> (I wanted to do it for port forwarding.)
>>
>> Any ideas what I should be looking for?
>>
>> TIA
>>
>> Slatts
Look in your router something along the lines of "
LAN Clients" and add your fixed IPs.
Chris
--
Superb hosting & domain name deals http://dn-22.co.uk
The Handyman http://www.looker.me.uk
The FlatPack Man http://www.flat-pack.info
aljuhani
05-18-08, 06:43 AM
On May 17, 8:57*pm, "Sla#s" <p...@KNOTslatts.net> wrote:
> I can't connect with fixed IP on a WPA Wireless network.
> Roaming and automaticly assigned *IPs work but when I try to set the two
> wireless machines to fixed IPs they won't connect. (one is WinXP, other
> Ubuntu)
> Gateway is 192.168.2.1 a wired machine is ...2.2 and I wanted the *two
> wireless ones to be ...2.3 & ...2.4
> (I wanted to do it for port forwarding.)
>
> Any ideas what I should be looking for?
>
> TIA
>
> Slatts
Ok when assigning a fixed IP,
- What is the netmask you are using.
- What is the output of IPconfig.
- What is the range of DHCP IP addresses defined within your router?
-aljuhani.
Adair Winter
05-18-08, 09:08 AM
"Sla#s" <phil@KNOTslatts.net> wrote in message
news:g0n6c4$cqe$2@energise.enta.net...
>I can't connect with fixed IP on a WPA Wireless network.
> Roaming and automaticly assigned IPs work but when I try to set the two
> wireless machines to fixed IPs they won't connect. (one is WinXP, other
> Ubuntu)
> Gateway is 192.168.2.1 a wired machine is ...2.2 and I wanted the two
> wireless ones to be ...2.3 & ...2.4
> (I wanted to do it for port forwarding.)
>
> Any ideas what I should be looking for?
You never mention DNS address, are you you using for a DNS IP?
To manually configure a machine with a static IP addrss you'll need four
things.
1. Static IP Address for each machine. check to see if there is an active
host by pinging the address while on DHCP.
2. Subnet Mask. More than likely will be set for you after you type in the
IP but should prolly be 255.255.255.0
3. Default Gateway, should be the IP address of your router/firewall/ap.
4. Primary DNS server. Either use the IP address of your router/firewall or
check with your ISP and use the actual DNS server IP address.
Should work.
Adair
Adair Winter wrote:
<SNIP>>>
>> Any ideas what I should be looking for?
>
> You never mention DNS address, are you using for a DNS IP?
>
Both the static ones of my provider, Open DNS and I also tried the gateway.
> To manually configure a machine with a static IP address you'll need
> four things.
>
> 1. Static IP Address for each machine. check to see if there is an
> active host by pinging the address while on DHCP.
>
That's what I'm not getting unless I let it get the IP automatically.
> 2. Subnet Mask. More than likely will be set for you after you type
> in the IP but should prolly be 255.255.255.0
>
Yes that just pops up when a static IP is entered.
> 3. Default Gateway, should be the IP address of your
> router/firewall/ap.
That is set OK at 192.168.2.1
> 4. Primary DNS server. Either use the IP address of your
> router/firewall or check with your ISP and use the actual DNS server
> IP address.
I've tried my providers ones (l95.74.***.***), 'Open DNS' ones and
currently, the local gateway. (l92.l68.2.l)
Slatts
------------------------------------------------------------------------------------
Belkin F5D8631(192. . .1), WinXP SP3(wired 'static IP' 192. . .2), Wireless
WinXP SP3 Media centre and Wireless Ubuntu 8.04.
STOP PRESS....
I think I've found the problem
From a review of the router:
"Unlike some competing routers, the N1 does not support DHCP reservation"
Slatts
Joker7 wrote:
<SNIP>
>>> Any ideas what I should be looking for?
>>>
>
> Look in your router something along the lines of "
> LAN Clients" and add your fixed IPs.
Interestingly although the router will show the connected machines IPs I can
find no provision for adding LAN clients manually.
This is the problem - From a review:
"Unlike some competing routers, the N1 does not support DHCP reservation"
Slatts
Sla#s wrote:
> Joker7 wrote:
> <SNIP>
>>>> Any ideas what I should be looking for?
>>>>
>>
>> Look in your router something along the lines of "
>> LAN Clients" and add your fixed IPs.
>
> Interestingly although the router will show the connected machines
> IPs I can find no provision for adding LAN clients manually.
huh ?
> This is the problem - From a review:
> "Unlike some competing routers, the N1 does not support DHCP
> reservation"
huh ?
Joker7 wrote:
> To restore balance to the world Sla#s wrote in
> g0n6c4$cqe$2@energise.enta.net
>>> I can't connect with fixed IP on a WPA Wireless network.
>>> Roaming and automaticly assigned IPs work but when I try to set the
>>> two wireless machines to fixed IPs they won't connect. (one is
>>> WinXP, other Ubuntu)
>>> Gateway is 192.168.2.1 a wired machine is ...2.2 and I wanted the
>>> two wireless ones to be ...2.3 & ...2.4
>>> (I wanted to do it for port forwarding.)
>>>
>>> Any ideas what I should be looking for?
>>>
>>> TIA
>>>
>>> Slatts
>
> Look in your router something along the lines of "
> LAN Clients" and add your fixed IPs.
>
> Chris
is that like "reserving" IP addresses within the DHCP pool range ?
ie - for poking holes in your pool for static IP vs correcting your DHCP
definition ?
Sla#s wrote:
>
> STOP PRESS....
> I think I've found the problem
>
> From a review of the router:
> "Unlike some competing routers, the N1 does not support DHCP
> reservation"
ok... so what's you DHCP range pool definition to support 3 computers ?
Why woud you put all IP addresses next to each other ?
vs say DHCP up at the 50, 100, 150, or 200 range
and leave the lower range for static addresses ?
For me - I always leave 1-50 for static....
and the DHCP is at the 150 range
Sla#s wrote:
> Adair Winter wrote:
> <SNIP>>>
>>> Any ideas what I should be looking for?
>>
>> You never mention DNS address, are you using for a DNS IP?
>>
> Both the static ones of my provider, Open DNS and I also tried the gateway.
>
>> To manually configure a machine with a static IP address you'll need
>> four things.
>>
>> 1. Static IP Address for each machine. check to see if there is an
>> active host by pinging the address while on DHCP.
>>
> That's what I'm not getting unless I let it get the IP automatically.
>
>> 2. Subnet Mask. More than likely will be set for you after you type
>> in the IP but should prolly be 255.255.255.0
>>
> Yes that just pops up when a static IP is entered.
>
>> 3. Default Gateway, should be the IP address of your
>> router/firewall/ap.
>
> That is set OK at 192.168.2.1
>
>> 4. Primary DNS server. Either use the IP address of your
>> router/firewall or check with your ISP and use the actual DNS server
>> IP address.
>
> I've tried my providers ones (l95.74.***.***), 'Open DNS' ones and
> currently, the local gateway. (l92.l68.2.l)
>
>
> Slatts
> ------------------------------------------------------------------------------------
>
> Belkin F5D8631(192. . .1), WinXP SP3(wired 'static IP' 192. . .2), Wireless
> WinXP SP3 Media centre and Wireless Ubuntu 8.04.
>
> STOP PRESS....
> I think I've found the problem
>
> From a review of the router:
> "Unlike some competing routers, the N1 does not support DHCP reservation"
>
> Slatts
>
>
The fact that it does not support DHCP reservation will not prevent
Static IP addressing from working. However it is not a good idea to use
Static Addresses that are within the DHCP pool, I would suggest that you
start by changing the DHCP Pool start from 192.168.2.2 to 192.168.2.50
and then give your computers static IP's 192.168.2.2..3...4.
Whar are you using to manage your network in Ubuntu, "Network Manager"
or something else.
To restore balance to the world Sla#s wrote in
g0pjfi$1h24$2@energise.enta.net
>> Joker7 wrote:
>> <SNIP>
>>>>> Any ideas what I should be looking for?
>>>>>
>>>
>>> Look in your router something along the lines of "
>>> LAN Clients" and add your fixed IPs.
>>
>> Interestingly although the router will show the connected machines
>> IPs I can find no provision for adding LAN clients manually.
>>
>> This is the problem - From a review:
>> "Unlike some competing routers, the N1 does not support DHCP
>> reservation"
>>
>> Slatts
Try: DHCP Configuration
Chris
--
Superb hosting & domain name deals http://dn-22.co.uk
The Handyman http://www.looker.me.uk
The FlatPack Man http://www.flat-pack.info
To restore balance to the world Sla#s wrote in
g0pjfi$1h24$2@energise.enta.net
>> Joker7 wrote:
>> <SNIP>
>>>>> Any ideas what I should be looking for?
>>>>>
>>>
>>> Look in your router something along the lines of "
>>> LAN Clients" and add your fixed IPs.
>>
>> Interestingly although the router will show the connected machines
>> IPs I can find no provision for adding LAN clients manually.
>>
>> This is the problem - From a review:
>> "Unlike some competing routers, the N1 does not support DHCP
>> reservation"
>>
>> Slatts
Whoops- just re-read your post it looks like you need a new router one that
will support DHCP Configuration..
Chris
--
Superb hosting & domain name deals http://dn-22.co.uk
The Handyman http://www.looker.me.uk
The FlatPack Man http://www.flat-pack.info
LR wrote:
<SNIP>
>>
> The fact that it does not support DHCP reservation will not prevent
> Static IP addressing from working. However it is not a good idea to
> use Static Addresses that are within the DHCP pool, I would suggest
> that you start by changing the DHCP Pool start from 192.168.2.2 to
> 192.168.2.50 and then give your computers static IP's
> 192.168.2.2..3...4.
Already done that.
Perhaps I should start the DHCP pool from 192.168.2.10 to allow the lower
number ones to be fixed...?
I'll give that a try tomorrow.
>...Whar are you using to manage your network in
> Ubuntu, "Network Manager" ...
Yes...
-----------------------------------------------------
Further to all this I now can't connect theUbuntu machine at all...! Even
the old way as "roaming".
Slatts
Sla#s wrote:
> Perhaps I should start the DHCP pool from 192.168.2.10 to allow the
> lower number ones to be fixed...?
> I'll give that a try tomorrow.
MAYBE START AT ---> 192.168.2.100
what's the facination with squeezing the IP numbers next to each other ?
you have about 250 addreses available in the segment !
Bill Kearney
05-18-08, 09:44 PM
> The fact that it does not support DHCP reservation will not prevent Static
> IP addressing from working. However it is not a good idea to use Static
> Addresses that are within the DHCP pool
Not a good idea? How about a TREMENDOUSLY BAD IDEA. Never, even do this.
Eventually you'll have a DHCP lease request run up against one already in
use statically. Some DCHP servers are smart enough to ping first before
leasing, but most aren't that smart.
What can be helpful is to set up a DHCP reservation. This way the DHCP
server always gives the same IP address to a device based on it's MAC
address. But not many SoHo class routers support configuring such lease
reservations.
Chris Davies
05-19-08, 04:02 PM
Sla#s <phil@knotslatts.net> wrote:
> "Unlike some competing routers, the N1 does not support DHCP reservation"
The easiest way of fudging this on a domestic consumer grade router is
simply to move the DHCP allocation range out of the way.
e.g. router = 192.168.1.254
dhcp range = 192.168.1.32-63
static range (PCs) = 192.168.1.1-31
static range (servers, printers, VoIP...) = 192.168.1.253-64
Chris
Bill Kearney wrote:
>> The fact that it does not support DHCP reservation will not prevent
>> Static IP addressing from working. However it is not a good idea to
>> use Static Addresses that are within the DHCP pool
>
> Not a good idea? How about a TREMENDOUSLY BAD IDEA. Never, even do
> this. Eventually you'll have a DHCP lease request run up against one
> already in use statically. Some DCHP servers are smart enough to
> ping first before leasing, but most aren't that smart.
>
> What can be helpful is to set up a DHCP reservation. This way the
> DHCP server always gives the same IP address to a device based on
> it's MAC address. But not many SoHo class routers support
> configuring such lease reservations.
(Ops Sorry - clicked wrong button)
.....
"..., the N1 does not support DHCP reservation"
Slatts
vBulletin® v3.7.3, Copyright ©2000-2008, Jelsoft Enterprises Ltd.