help - WRTP54G Using Only Wireless 2 Connect

[jccboca]

Hello All,

I have a dilemma - I have a linksys/vonage WRPT54G and I a just
relocated to an area that only has wireless access. I am runing Vista
Home premium on a new Gateway laptop.

I was told that I could get a crossover cable and use the ethernet port
in my laptop ( while connected to to the web via the internal wireless
card ) to the wan/lan port in the WRPT54G to get connectivity to the
WRPT54G.

BTW, I also enabled Internet Connection Sharing for the wireless
connection with auto DHCP.

When I hooked up the crossover cable to the WRTP54G,, the power,
wireless and internet blue lights do come on and I can even see the
unsecured linksys router in available networks, however with only local
connectivity.

The only way I can access the firmware at the router is to change over
to connect to the linksys network ( instead of the regular wireless
connection from the internal card) with the password admin/admin.

Once inside the firmware, I can not get the router to get an ip addy,
it just remains blank, even after I press dhcp refresh/renew.

I tried everything, even calling linksys who just put me on hold.

Any help would really be appreciated!

Thanks,
JCC


------------------------------------------------------------------------
View this thread: http://www.wirelessforums.org/showthread.php?t=36092
http://www.wirelessforums.org

[qwerty]

On Jan 3, 5:28*am, jccboca <jccboca.32m...@no-mx.wirelessforums.org>
wrote:
> Hello All,
>
> I have a dilemma - I have a linksys/vonage WRPT54G and I a just
> relocated to an area that only has wireless access. I am runing Vista
> Home premium on a new Gateway laptop.
>
> I was told that I could get a crossover cable and use the ethernet port
> in my laptop ( while connected to to the web via the internal wireless
> card ) to the wan/lan port in the WRPT54G to get connectivity to the
> WRPT54G.
>
> BTW, I also enabled Internet Connection Sharing for the wireless
> connection with auto DHCP.
>
> When I hooked up the crossover cable to the WRTP54G,, the power,
> wireless and internet blue lights do come on and I can even see the
> unsecured linksys router in available networks, however with only local
> connectivity.
>
> The only way I can access the firmware at the router is to change over
> to connect to the linksys network ( instead of the regular wireless
> connection from the internal card) with the password admin/admin.
>
> Once inside the firmware, I can not get the router to get an ip addy,
> it just remains blank, even after I press dhcp refresh/renew.
>
> I tried everything, even calling linksys who just put me on hold.
>
> Any help would really be appreciated!
>
> Thanks,
> JCC
>
> ------------------------------------------------------------------------
> View this thread:http://www.wirelessforums.org/showthread.php?t=36092http://www.wirelessforums.org

Hi,

U did not mention the name of your internet service provider.
If you have connected the Laptop to the WAN port on the router you
will not get an IP Address.
Laptops/any comp should be conn to any of the 4 LAN port's on the
router.
WAN port is meant for the connection that is coming from your Internet
service provider.
In your case u told that your area has only wireless access, then
there is no way you can use the router for internet connection.
You need to have a normal internet connection through a modem for u
to access the internet through the router.

ISP---->Modem--->Router--->Comp's

the connection should be like this.


Please do reply.
Also take a look at this website http://thenetworld.nexo.com/ for any
networking info.

thanks.
Manu S